|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
SHOULDER SPECIFICATION Item: Type: CRYSTAL SMD0503 Optional SHOULDER SMD0503 CRYSTAL Scope This specification shall cover the characteristics of SMD 5x3.2 crystal. Ultra small package Wide Frequency Range Electrical Specification Parameter Nominal Frequency Frequency Tolerance (at 25C) Frequency Stability Oscilation Mode Equivalent Series resistance Drive Level Operating Temperature Range Storage Temperature Load Capacitance Shunt Capacitance Aging (at 25C) Insulation Resistance Value 10.00 to 80.000 MHz + 30 PPM (Maximum) +30 PPM (Maximum) Fundamental 50 1.0 mW (Maximum) -20 to + 70C Standard (or Optional) -40 to + 85C 10 pF to Series < 7 PF + 3 ppM per year > 500 M at DC 100V Mechanical Dimensions (All in mm) SMD0503 SHOULDER INDUSTRIA ELETRONICA LTDA Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG Page 2 of 5 www.hdshoulder.com.br SHOULDER SMD0503 CRYSTAL Mechanical Specification Conditions 1. Vibration test Frequency Amplitude Sweep Duration 2. Drop test Method of drop Dropping floor Height Number of drops Natural drop Hard wood board 30cm 3 times Frequency and wave form of tested products must remain within specifications. Results 10 ~ 55Hz 0.762mm 1.0 minute 2 hours Frequency and wave form of tested products must remain within specifications. Environmental Specification Conditions 1. Temperature test 1) at -55C, 30 minutes 2) at +25C, 10~15 minutes Steps of cycle Temperature cycling test 3) at +85C, 30 minutes 4) at +25C, 10~15 minutes Number of cycles 3 times 2. Aging test Temperature +85C 20C Length of test 96 hours 3. Salt spray test Temperature +35C 2C Length of test 48 hours NaCI % 5% 4. Humidity test Temperature +40C 2C Relative humidity 90 ~ 95% Length of test 96 hours Frequency and wave form of tested products must remain within specifications. Results Deviation of frequency must be less than 3ppM. There should be no stain on surface of products. a) Insulation resistance must be 500 M/100 Vac minimum. b) Resistance and wave form must remain within specifications. Soldering SHOULDER INDUSTRIA ELETRONICA LTDA Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG Page 3 of 5 www.hdshoulder.com.br SHOULDER SMD0503 CRYSTAL Tape Specifications (All in mm) Reeling Quantity - 1000pcs / reel Carrier Tape Dimensions W 16+ 0.3 F 5.5+ 0.05 P0 4.0+ 0.1 P1 9.0+ 0.1 D0 1.5+ 0.1 D1 1.6 + 0.25 t1 0.3+ 0.03 t2 1.7+ 0.1 A 4.2+ 0.1 B 6+ 0.1 SMD0503 CRYSTAL Part Numbering System (Example) SHOULDER INDUSTRIA ELETRONICA LTDA Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG Page 4 of 5 www.hdshoulder.com.br SHOULDER SMD0503 CRYSTAL SMD0503 11.0592 F 20 30 30 A T Type Nominal Frequency (in MHz) Vibration Mode Load Capacitance Frequency Tolerance Frequency Stability Operating Temperature Range A -20C to 70C -10C to 60C 0C to 50C -30C to 80C -40C to 85C Option (can be blank) SMD0503 49S-SMD 49S2-SMD SMD0804 SMD0705 SMD0603 SMD0402 Enter the nominal frequency (3 digits after dot) or up to last significant digit (different than zero) S = Series F = Fund Or enter load capacitance: 10 to 33 for parallel Indicate the tolerance value in PPM Indicate the stability over temperature range value in PPM B C D E S= Standard X= Additional Specifications T= Tape and Reel SHOULDER INDUSTRIA ELETRONICA LTDA Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG Page 5 of 5 www.hdshoulder.com.br |
Price & Availability of SMD0603 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |